Unable to get DSD+ Fastlane to recognize my RSPdx

This topic has 7 replies, 2 voices, and was last updated by .

Viewing 8 posts - 1 through 8 (of 8 total)

Author

Posts
October 22, 2022 at 5:25 pm #2120
krakatau
Participant
Hi folks,
Brand new to the SDT space. I am a techie, so throw anything at me – in terms of stuff that needs to be done.
I ‘ve gotten started pretty well with SW and all and even with DSD+ in combination with SDRuno.
Yet, I am unable to get DSD+ Fastlane to recognize my RSPdx.
I hope that it’s not an issue with it not being supported.

Does anyone use this combination? I am using Win10.
October 22, 2022 at 5:34 pm #2121
krakatau
Participant
A bit of extra details…

Based on this:

Single-dongle monitoring:

To use a single device, run the 1R.bat file to start DSD+,
then run the appropriate batch file for your device:

DVB-T dongle: FMP24-CC.bat

Airspy: FMPA-CC.bat

SDRPLay: FMPP-CC.bat

I ran 1r.bat and then FMPP-cc.bat. Also tried to add the serial # to the FMPP.cfg. No luck

———————-
Probably a further down the road thing, but I also get this error:
Initiating FMPx link using link ID 20001…
FMPx link error = -5
[Server is not listening on selected link ID]
- This reply was modified 2 years, 1 month ago by .
October 23, 2022 at 3:56 pm #2124
krakatau
Participant
Thanks folks.

Guess what?…. If I try to open it right after I close it – so open > error > close > open – it recognizes my RSPdx!??
Yeah, it works. With FMPP and the S/N specified in the cfg.

BUT… now I barely see any transmissions (green peaks) and when I get to them I get silence, as if it wouldn’t decode them, or there is no active call. I’ve scanned the the whole band. What gives?

This is a cab company frequency, so there’s no way that there would be no active comms.
How can I troubleshoot this? I’ve also loaded the local frequencies from the location indicated in Notes. If at all relevant: I am located in ON, Canada.
October 23, 2022 at 4:25 pm #2125
krakatau
Participant
Also, there is no event log window opening. I see only the cmd line window for FMPP.
October 23, 2022 at 6:51 pm #2126
krakatau
Participant
The attached should work, but I hear nothing. Once I tune to it the noise is gone and I hear nothing.
Without a WMPP event log, I don’t know what’s happening.
I am unable to decode ANY received channel using WMPP.
What am I doing wrong?
Attachments:
1. should-work.png
October 23, 2022 at 8:33 pm #2128
krakatau
Participant
Sorry folks, I figured most of the stuff out.

Here’s where I’m at, using my single SDR – in my case the RSPdx:
FMPP running properly. Setting used for FMPP-cc.bat: -rc -i1 -o20001 -f421.2125
CC is fed nicely on 20001, decoding like crazy – lots of stations, etc. Using default cc.bat: DSDPlus -rc -i20001 -v3 -wsl400.2 -wss100.200 -wel0.1 -wcl0.445 -wes400.520 >>CC.log
I can’t get the voice part going. If I try to run FMPP-vc.bat with the default: FMPP -rv -i2 -o20002, I get -i2 error, as I have only one device. If I run it with FMPP -rv -i1 -o20002, I get an error of in use, as I am using it for the cc decoding.
vc.bat: DSDPlus -rv -Pwav -i20002 -v3 -wsl400.210 -wss100.200 -wel172.522 -wcl528.0 >>VC.log

How am I making this work? I understood that DSD+ Fastlane is switching between cc and vc and I can use just one RDS – my RSPdx connected on port 1.
How am I to set it up, since the (-i2) default doesn’t work?

Do I have to output from DSD+ to a voice cable and pipe that to vc.bat?

October 23, 2022 at 8:43 pm #2129

krakatau

Participant

Fixed! You must use the 1r.bat for 1 RTL-SDR. It works!
Thanks, sorry for too many messages. Cheers

February 22, 2024 at 9:57 am #2294

Avery78

Participant

It appears that you are experiencing compatibility difficulties with DSD+ Fastlane and your RSPdx. Have you searched for driver upgrades or explored internet forums for troubleshooting advice? Sometimes community assistance can give useful information.

Viewing 8 posts - 1 through 8 (of 8 total)

You must be logged in to reply to this topic.

Attachments: